Spn 1347 fmi 3.

Cummins ISL CM850 (2003-06) Fault Code: 272 (Auto) PID: SID 126 SPN: 1347 FMI: 3 High Fuel Pressure Solenoid Valve Circuit - Voltage Above Normal or Shorted to High Source. Electronic fuel control actuator shorted high. This fault becomes active when the ECM detects an open in the electronic fuel control actuator circuit. Causes of this fault ...

Spn 1347 fmi 3. Things To Know About Spn 1347 fmi 3.

Section 25.1SPN 2797/FMI 3. This diagnosis is typically injector #1, 2, or 3 needle control valve circuit has a short to battery/power.‪. Check as follows:‪. Disconnect the Front Injector Harness 14–pin connector. Turn the ignition ON (key ON, engine OFF). Measure the voltage between pin 1 on the MCM side of the Front Injector Harness 14 ...SPN#1347, FMI#3. engine switch to OFF (TM 5-3895-385-10), and proceed to. SPN#1347, FMI#3. troubleshooting procedure. 2. If fault code SPN#1347, FMI#3. is not displayed, proceed to. next test. 6. Check active engine faults. 1. If fault code SPN#627, FMI#2 is. screen for fault code SPN#627, displayed, turn keyless engine.We have a 2007 Peterbilt 389 cummins ISX engine 600 we are getting the fault code J1939 SA 49 SPN 829 FMI 3. Peterbilt - Answered by a verified Technician We use cookies to give you the best possible experience on our website.Yesterday morning, it started getting the code SPN 1347 FMI 3. The code - Answered by a verified Technician. We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.

SPN 3701 - Diesel Particulate Filter Status Level 3-5. This occurs when the unit has not been able to have a successful regeneration, so the particular matter accumulation has an excessive amount inside the DPF. Common Fix: An engine manufacture diagnostic tool/ software would have to be used to force a regeneration on the unit's exhaust system.

SPN: 1347. FMI: 7. LAMP: Yellow. SRT: Front Pumping Element. The electronic control module (ECM) has detected a malfunction in the front pumping element. The front pumping element in the Cummins accumulator pump system (CAPS) consists of the front barrel and plunger, front pumping control valve, and the front check valve in the accumulator.

Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 6647 PID: SPN: 6780 FMI: 3 Aftertreatment 1 Diesel Particulate Filter Soot Temperature Sensor- Voltage Above Normal or Shorted to High Source. Circuit Description The aftertreatment particulate matter sensor is a smart device and communicates with the engine control module ...Fmi 18 spn 792 Fmi 3 spn 3464 Fmi 7 spn 3463 - Answered by a verified Technician. We use cookies to give you the best possible experience on our website. ... Good day. 2011 Cummins isx cm2250 showing spn 1347 fmi 3, spn 157 fmi 16 ...Cummins ISB6.7 CM2150 (2007-09) Fault Code: 272 PID: SID 126 SPN: 1347 FMI: 3 Fuel Pump Pressurizing Assembly 1 Circuit – Voltage Above Normal or Shorted …If you are getting that fault from the touch screen, push on that fault to open the next screen that will tell you the FMI #. P0473 SPN 1209 FMI 3 - Pre-turbine air pressure over range fault P0472 SPN 1209 FMI 4 - Pre-turbine air pressure under range fault P0471 SPN 1209 FMI 2 - Pre-turbine air pressure out of range at powerup

SPN 1321, FMI 3 - Start Relay Coil . Page 189 and 190: SPN 1348, FMI 5 - Fuel Pump Relay C. Page 191 and 192: SPN 1347, FMI 5 - Fuel Pump Relay G. Page 193 and 194: SPN 1347, FMI 6 - Fuel Pump Relay C. Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, Page 197 and 198: SPN 515, FMI 16 - RPM Above Fuel Re. Page 199 and 200:

CODES: Fault Code: 2265. PID (P), SID (S): S126. SPN: 1075. FMI: 3. Lamp: Amber. REASON: Electric Lift Pump for Engine Fuel Supply Circuit - Voltage Above Normal or Shorted to High Source. High voltage or open detected at the fuel lift pump signal circuit. EFFECT: Engine can be difficult to start.

SPN 515, FMI 16 - RPM Above Fuel Rev Limit Level. Diagnostic Aids. NOTE: If any other DTCs are present, diagnose those first. Ensure that no programmed governor speeds exceed the limit set in the ...FMI SPN FMI DESCRIPTION QSB QSC QSL9 QSM1 1 QSX1 5 QSK19 QSK23 QS T 30 QSK45 QSK60 QSK78 HHP Level Number (**) 111 (Red) S254 12 629 12 ... 3 1347 3 High Fuel Pressure Solenoid Valve #1 Circuit X- shorted high 273 (Yellow) S127 4 1348 4 High Fuel Pressure Solenoid Valve #2 Circuit - shorted low X 274SPN FMI COMPONENT P-CODE CONDITION; Displayed on instrument cluster Displayed on Digital Wrench diagnostic software; 29. 3. Accelerator Position 2 ... 1347. 3. Fuel Pump Driver Circuit. P0232. Voltage Above Normal, Or Shorted To High Source. 1347. 4. P0231. Voltage Below Normal, Or Shorted To Low Source. 1347. 5 ...Fault Code: 691. PID (P), SID (S): P351. SPN: 1172. FMI: 3/3. Lamp: AMBER. SRT: ISB with CM2150 - Ambient Air Temperature Sensor Circuit. REASON: Turbocharger 1 Compressor Inlet Temperature Sensor Circuit - Voltage Above Normal or Shorted to High Source. High signal voltage detected at the turbocharger compressor inlet air temperature circuit.SPN: 1348: 1347: 1079: 1079: FMI: 3: 6: 4: 3: MIL: ON: ON: ON: ON: Detected Item • Shorted relay pull in coil • relay driver circuit shorted to voltage in wire harness • Wiring harness short to ground • ECM malfunction • Wiring harness short to 12.0 V power • ECM malfunction: DTC Set Preconditions • Engine Running • Key-On ...

Fault Code: 133. PID (P), SID (S): P029. SPN: 974. FMI: 3/3. Lamp: None. SRT: REASON: Remote Accelerator Pedal or Lever Position Sensor 1 Circuit - Voltage Above Normal, or shorted to High Source. High voltage detected at remote accelerator pedal position circuit. EFFECT: Remote accelerator will not operate.SPN: 1189 FMI: 3. Description: TC2WG short to PWR Troubleshooting: The Turbocharger 2 Wastegate Control (TC2WC) is a valve in the number two turbo that diverts exhaust gases away from the turbine wheel. Diversion of exhaust gases from the turbo regulates the turbine speed. Probable causes: 1) TC2WG control shorted to B+Fault Code: 451. PID (P), SID (S): P157. SPN: 157. FMI: 3. Lamp: AMBER. SRT: ISB with CM2150 - Fuel Rail Pressure Sensor Circuit. REASON: Injector Metering Rail Number 1 Pressure Sensor Circuit - Voltage Above Normal or Shorted to High Source. High signal voltage detected at rail fuel pressure sensor circuit.SPN-1235, SPN-1347, SPN-3058, SPN-3216, SPN-3217, SPN-5024, SPN-5109, ... Spn 0412 Fmi 3.Egr recirculation 1 temp Voltage above normal or shorted to high source 2016 peterbilt 579 mx13 Vin 6gd335206Why is this code present ...SPN: 51: 105: 108: FMI: 3: 0: 1: MIL: ON: ON: ON: Detected Item. TPS circuit in the harness short to power. TPS malfunction. Intake air temperature abnormality (High side stage 2). Sensor out of calibration. Loss for 5V reference feed. (5V_ext1) to MAP. Signal wire open or shorted to ground: DTC Set Preconditions. Key-On, Engine …

SPN = Suspect Parameter Number / FMI = Failure Mode Indicator; Trouble Code SPN FMI P-CODE Condition; Throttle Position Sensor 1 Voltage High. 51. 3. P0123. This Trouble Code sets if the Throttle Position Sensor Signal is above 4.61 Volts. Can be caused by Damaged Wiring, a faulty Throttle Position Sensor or ECU / Connections.Refer to OEM literature and repair the wire between the ACM and the line heaters. Verify repair. 4 SPN 3599/FMI 4 - EPA10. High Side Digital Output 3 Circuit Failed Low. Table 3. SPN 3599/FMI 4. Description. This Code Sets When the Aftertreatment Control Module (ACM) Detects a Short to Ground on Pins 9, 15, or 39.

Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 3332 PID: SPN: 1347 FMI: 2/2 Engine Fuel Pump Pressurizing Assembly 1 – Data Erratic, Intermittent, or Incorrect520520 - 4 = ABS Ground (Front Axle) -. voltage below normal or shorted low Failure detection 'ShortGnd' at AbsGround (Front Axle) A short circuit to permanent GND-level at the relevant low-side switch is detected: - After 150 ms (if the low side switch is open). - After 2000 ms (if the low side switch is closed). 3: sensor volt2 (+5vdc)above norm or short high: 1080: 4: sensor volt2 (+5vdc)below norm or short low: 1109: 31: eng prot system approaching shutdown: 1110: 31: eng prot system shut eng down: spn fmi description; 1347: 5: fuel pump assy 1 ckt open, shorted ground or ovload: 1347: 7: fuel pump assy 1 rail pressure cont mismatch: 1347: 10: fuel ... Hello TxId: 0 SPN: 171 - Ambient Air Temperature FMI: 2 (Erratic, Intermittent, or Incorrect) Count: 1 TxId: 58 SPN: 520211 FMI: 7 (Not … read more. Andy. truck /coach technician. Vocational, Technical or Tra... 214 satisfied customers. Codes SA 0 SPN 3720 FMI 15 Cummins engine ixs.SPN 1321, FMI 3 - Start Relay Coil . Page 189 and 190: SPN 1348, FMI 5 - Fuel Pump Relay C. Page 191 and 192: SPN 1347, FMI 5 - Fuel Pump Relay G. Page 193 and 194: SPN 1347, FMI 6 - Fuel Pump Relay C. Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, Page 197 and 198: SPN 515, FMI 16 - RPM Above Fuel Re. Page 199 and 200:Fault Code: 449. PID (P), SID (S): P94. SPN: 157. FMI: 0. SRT: REASON: Injector Metering Rail Number 1 Pressure - Data Valid But Above Normal Operating Range - Most Severe Level. The ECM has detected that fuel pressure in the fuel rail is higher than the fuel pressure relief valve. EFFECT: None or possible engine noise associated with …

Dec 15, 2013 · Dec 15, 2013. #1. I have a IR G 240 generator. When i load bank the unit and get about 150 kw of load the rpm starts to fall and i get a spn 1347 fmi 7 code. I have changed the mechanical fuel pump and the high press pump also the press sensor on the fuel rail with out success. Also checked the relief valve on the rail for leakage when running ...

FMI SPN FMI DESCRIPTION QSB QSC QSL9 QSM1 1 QSX1 5 QSK19 QSK23 QS T 30 QSK45 QSK60 QSK78 HHP Level Number (**) 111 (Red) S254 12 629 12 ... 3 1347 3 High Fuel Pressure Solenoid Valve #1 Circuit X- shorted high 273 (Yellow) S127 4 1348 4 High Fuel Pressure Solenoid Valve #2 Circuit - shorted low X 274

SPN: 1347 FMI: 3 SPN: 1347 FMI: 4 SPN: 6971 FMI: 5I have 2012 freightliner showing above codes engines is losing power read more. Wayne. Journeyman. Vocational, Technical or Tra... 6,177 satisfied customers. Show more. Disclaimer: Information in questions answers, and Show Less. Disclaimer: Information in questions, answers, and other posts on ...The SPN number you provided refers to an issue with the "Auxillary pressure sensor 1". Ask Your Own Medium and Heavy Trucks Question. It like ecu cab over voltage or something What's the auxiliary pressure sensor. Technician: TomcM28. Currently researching. Ask Your Own Medium and Heavy Trucks Question.Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 3332 PID: SPN: 1347 FMI: 2/2 Engine Fuel Pump Pressurizing Assembly 1 – Data Erratic, Intermittent, or Incorrect. Lamp: Amber. Reason: The fuel pump actuator circuit resistance is too high or too low, or an intermittent connection has been detected.If you are getting that fault from the touch screen, push on that fault to open the next screen that will tell you the FMI #. P0473 SPN 1209 FMI 3 - Pre-turbine air pressure over range fault P0472 SPN 1209 FMI 4 - Pre-turbine air pressure under range fault P0471 SPN 1209 FMI 2 - Pre-turbine air pressure out of range at powerupFault Code: 134. PID (P), SID (S): P372. SPN: 974. FMI: 4/4. Lamp: Red. REASON: Low voltage detected at remote accelerator position signal circuit. EFFECT: Remote accelerator will not operate. Circuit Description: The remote accelerator position sensor is a potentiometer attached to the remote accelerator lever.Fault Code: 451. PID (P), SID (S): P157. SPN: 157. FMI: 3. Lamp: AMBER. SRT: ISB with CM2150 - Fuel Rail Pressure Sensor Circuit. REASON: Injector Metering Rail Number 1 Pressure Sensor Circuit - Voltage Above Normal or Shorted to High Source. High signal voltage detected at rail fuel pressure sensor circuit.Section 57.1SPN 647/FMI 3. Turn the ignition OFF. Disconnect the fan control solenoid connector. Turn the ignition ON (key On, engine OFF). Measure the voltage between pin 1 of the fan control solenoid connector and ground. If the voltage is greater than 11.5 volts, repair the short to power between pin 1 of the fan control solenoid connector ...Check for multiple codes. If 1176/3, 1172/3, 100/3 and 175/3 are present, repair the open between pin 105 on the 120-pin MCM connector and the associated sensors. Refer to "88.2.1.1 Verify Repairs" . If 1176/3 and 1172/3 are present, go to step 7 . If only 1176/2 is present, go to step 4 . Turn the ignition OFF.Fault Code: 281. PID (P), SID (S): S126. SPN: 1347. FMI: 7. Lamp: Amber. REASON: Fuel Pump Pressurizing Assembly 1 - Mechanical System Not Responding Properly or Out of Adjustment. A pumping imbalance between the front and rear pumping plungers has been. detected. EFFECT: Engine will not run or possible low power.• SPN 94/FMI 15 or 16 Fuel Filter Plugged • SPN 157/FMI 1 Rail Pressure too High • SPN 164/FMI (All) Rail Pressure Sensor Faults • SPN 174/FMI 0 Fuel Temperature too High • SPN 1077/FMI 5 or 6 Quantity Control Valve Current • SPN 1077/FMI 14 High Pressure Leakage Too High • SPN 520251/FMI (All) PCV High Side ErrorCheck for multiple codes. If the fault code SPN 3482/FMI 5 is active, in addition to SPN 3471/FMI 5, repair open circuit between pin 64 of the Motor Control Module (MCM) 120-pin connector and pin 2 of the Electronic Dosing Valve (EDV) and pin 2 of the Fuel Cutoff Valve (FCV) sensors. If the only fault code SPN 3471/FMI 5 is active, Go to step 3.

Code 1347-7 on a 2007 John Deere 200DLC Excavator. Mechanic's Assistant: Sometimes things that you think will be really complicated end up being easy to fix. The Heavy Equipment Mechanic I'm going to connect you with knows all the tricks and shortcuts. Code 1347-7 on a 2007 John Deere 200DLC Excavator what does it mean.Cummins X15 CM2350 X116B Performance Series (2018 & Newer) Fault Code: 6647 PID: SPN: 6780 FMI: 3 Aftertreatment 1 Diesel Particulate Filter Soot Temperature Sensor- Voltage Above Normal or Shorted to High Source. Circuit Description The aftertreatment particulate matter sensor is a smart device and communicates with the engine control module ...Issue Description. 1. Check engine light (CEL) is illuminated, AND. 2. Fuel gauge has ceased functioning, AND. 3. Fault code SPN 96 FMI 3 is present when the appropriate scan tool is connected. If all three of the above conditions exist, the fuel gauge issue is less likely to be afailure with any component or parts. Instead, such conditions can ...Instagram:https://instagram. kub power outage map knoxville tn7300 gateway blvdinternet outage lexington kypierce county wa property search I have a 2018 peterbilt with MX13. Tried died would not run, have codes SPN 1347 fmi 16. 156 fmi 3, 3480 fmi 17, spn94 fmi 10, spn 94 fmi 2. The company changed fuel filters that did nothing, I dont have any experinece on these truck. Not sure where to start or if Fuel rail could be problem? any insight would be great. philips universal remote 4 digit codes for vizio tvhalo salon melrose The SPN number you provided refers to an issue with the "Auxillary pressure sensor 1". Ask Your Own Medium and Heavy Trucks Question. It like ecu cab over voltage or something What's the auxiliary pressure sensor. Technician: TomcM28. Currently researching. Ask Your Own Medium and Heavy Trucks Question. wisp salon parker SPN 1347, FMI 6 - Fuel Pump Relay C. Page 195 and 196: SPN 1213, FMI 5 - MIL Open Key On, Page 197 and 198: SPN 515, FMI 16 - RPM Above Fuel Re. ... SPN 91, FMI 3 - FPP1 Voltage High F. Page 295 and 296: SPN 520199, FMI11 - FPP2 Invalid Vo. Page 297 and 298: SPN 91, FMI 16 - FPP1 Higher than F.I have a 2019 Paccar mx13. Spn 4331 fin 20 code comes up Fault Code. Mechanic's Assistant: Im sorry to hear that youre experiencing a fault code with your 2019 Paccar MX13 engine, but I can connect you with an RV Mechanic who will be able to help you diagnose and resolve the issue. Have you noticed any specific issues or issues with your RV ...SPN#1347, FMI#3 ― High Voltage or Open Circuit At Fuel Pump Actuator-- Continued. MALFUNCTION. ... Vol 3 and WP 0448, Vol 3, Figure. 32). 2. If resistance is less ...